Old 1930 Electric Motor (OLD TOOLS RESTORATION)

Dipublikasikan tanggal 6 Des 2020
In this video you will see the restoration of a very old electric motor, from what I could find out it is from the year 1930 approximately, below I will leave you a little history about the company that manufactured this emblematic motor.

EMF Dordt is the name by which Willem Smit & Co.'s Electromotorenfabriek Dordrecht became known. This company existed from 1910 to 1977 in Dordrecht, in the Dutch province of South Holland, and the company manufactured electric motors.

History
EMF Dordt originated from the Smit Slikkerveer company and was founded by Willem Benjamin Smit. As the demand for electric motors increased, Smit Slikkerveer began to focus on large, specialty motors and generators. Series production of the most common engines would have to take place in a separate factory and a site for this was found in Dordrecht. Therefore, the company used the name: Smit Dordt as its logo. It was agreed that the engines manufactured in Dordrecht should not exceed 15 hp (11 kW). The largest engines would be manufactured at Slikkerveer.

In 1914 the limit was increased to 18 CV and in 1915 to 30 CV. In 1918, however, the demand for engines over 30 hp was also met and now EMF Dordt became a competitor to Smit Slikkerveer. The company name has now been changed to EMF Dordt. The company grew well. The registered capital (NLG 200,000) already doubled after two years (in 1913) and even increased to NLG 1 million in 1918. At that time it employed 160 people, in 1920 to 180. In addition to the factory (three floors) at Korten Parallelweg, the company also owned a factory building in 's-Gravendeelsedijk (including dyers). The 1920s were reasonably prosperous and the company was not even relatively affected by the economic crisis of the 1930s. In 1933, the Vereenigde IJzerfabrieken electric motor construction department became De Vijf in Doetinchem taken. In mid-1932, the NV Electric Machine Company, abbreviated EMO, was founded as a subsidiary, into which the manufacture of household items such as vacuum cleaners was incorporated. After initial success, it was liquidated again in 1940.

Some links of historical interest:
www.youtube.com/watch?v=-F_-U...
www.youtube.com/watch?v=uNsFG...

Komentar

  • excelente... muy buen gusto

  • Perchè hai messo fondo scala 200k per misurare pochi ohm di avvolgimento?

  • Soy un amante de las restauraciones y me gustó mucho revivir ese viejo pero inigualable motor un saludo desde Colombia

  • Браво! Отличная работа!)

  • Te felicito quedo de lujo, estos videos son lo mas

  • Is that oven cleaning you spray on this stuff to make it look worse swear its oven cleaner

  • Mis respetos, sea de 1930 o del 2000, es un trabajo extraordinario. Sos "UN MOUSTRO"..Espero ver un proximo trabajo..👍👍👍💯

  • Después de leer que no tienes estudio sobre eso. En este momento me pongo de pie y aplaudo. 👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏🇺🇾

  • Ganz wichtig bei solchen Motoren: Je nach Einbaulage, also stehend, oder hängend an der Wand, muss unbedingt vorn und hinten das Lagerschild gedreht werden, damit der Ölschöpfring arbeiten kann.

  • Tu es vraiment geni felicitation , grand salut pour vous.

  • Почёт и уважение человеку ...умелому +++++

  • Harika . Emeğinize sağlık

  • Amazing work, brilliant! How the hell does this video have 2.6K dislikes! You should all be ashamed!

  • why slow?

  • 2:08 sin protección?, buen trabajo

  • Nice!

  • 👍👍👍

  • una maravilla.

  • this kind of technology in 1930 ? i can't believe it.

  • Artista. Súper. Top 10.

  • Severo señor, verdad quedó mejor qué nuevo,😃👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏👏

  • Лайк минимум за то что перемотку поменял!

  • I had a question, why didn't you pack those bearings with grease? Thank you for a great video!

    • lol... nevermind! I would have packed them before installing! my bad!

  • Tremenda restauración! Un Profesional sin ninguna duda. Hasta el bobinado hiciste. Miré muchas restauraciones pero esta una Joya. Además con nuestro idioma, que pocas veces se encuentra en vídeos de restauración. Muy buen trabajo che!. Me suscribo ya y a ver que otras cosas hiciste. Gracias.

  • Onde você encontrou essa relíquia?

  • Hammer Handwerker!!!

  • Gutes Video! 100 Jahre später und wir haben noch die selbe Technik!? Heftig traurig! Aber Elektroautos! Das ist wahre Erfindung...🙈🤦‍♀️

  • Great👍👍👏🏻👏🏻👏🏻👏🏻

  • 👍👍💪💪❤️❤️🙏🙏

  • painstaking work

  • Grande colega yo tengo mucho trabajo que no tengo tiempo de pintarlos y todavía bobino motores de bombas marelli que tienen 60 años y siguen prestando servicio felicitaciones!

  • Please..restore my heart..😁👍

  • The winding won't last long without a real dip & bake or at least a pour on apoxy. Still a really nice restoration.

  • а это что за устройство? 5:00

    • Es un interruptor centrífugo

  • Ну и зачем?

  • Ni es tan viejo: TIENE RULEMANES

  • комментарий в поддержку канала спасибо за информацию всего хорошего вам

  • Подшипники больно легко зашли - видать, пескоструем хорошо так сняло посадочное место.

  • Ready for again till..year2130.. wow..bro you have golden hands.. Big fan of your... Luv from india...

  • @My Relics I know you guys love doing those wire diagrams... But Shouldn't there be (by now) I standard way of wrapping those wires based on efficiency and according to the amount of spacers available? I mean just because those wires were originally wrapped a certain way, couldn't you deviate from that norm to come up with a more efficient way of directing those currents? If I sound completely out of order here, I'm sorry. It's just that electricity only has a finite way of making that motor turn. Which should be up to the builder for interpretation. does that make any sense?

    • Creo que tiene sentido lo que comentas ... Pero al no tener ni idea de electrónica me limité a clonar el bobinado original

  • 12:15 Ok I fixed this and got some spare cables too!

  • Залипательно а ещё паучительно

  • tengo el mismo multimetro

  • The rice plate is very delicious. Thank you for sharing offline

  • Hello! Is it a syncronous motor? For what there are an electric brushes?

    • Es un interruptor centrífugo

  • Em 2130 quem sabe outro gênio , não revitalise e faça um vídeo também... excelente trabalho....

  • Soy un gran admirador de Meine Mechaniker, pero tu trabajo de rebobinado, nunca se lo habia visto. Por los productos, diria que sos de 🇦🇷pero es verdad que también podrian estar en el resto de Latinoamerica.

    • Soy de España ! Saludos !

  • A true electrical engineer

  • Интересо, на сколько часов работы хватало таких электро щёток?

  • After watching this restoration I had to subscribe to this channel. You do really nice work.

  • incridible work happy this is nice

  • Перемотка статора - большое искусство в бытовых условиях, уважение и поддержка. Красиво!

  • Nicely done thanks for sharing incredible job. I was a little surprised at the R.P.M.

  • عمل في غاية الروعة والاتقان .

  • Es un chingon un video 100 por ciento valido media hora en mi vida que vale la pena..

  • Класс. 👍👍👍👍👍 Отличная работа. По оборотам на 1000 похож, а на бирке 1500 написано.

  • Esse Restaurador é um gênio. Parabéns pelo seu trabalho

  • No ficou bueno mucho barulho Hace de nuevo

  • Awesome!

  • Electromotor uit Holland

  • Походу с обмоткой накосячил

  • Qual é o rpm e quantos cv.

  • My hat is off to you man! Rewiring an electric stator is no small feat. Awesome just awesome. The entire resto was just beautiful. Congrats!

  • Sin lugar a duda lo artesanal convertido en restauración, te quedó perfecto

  • 👏👏👏👏👏👏👏

  • Thank you for clean and good job God bless you

  • Каждое видео доводит до экстаза перфекционистов.

  • Результат ремонта : повреждение болгаркой вала по посадочной поверхности, согнутая крыльчатка безграмотным снятием ,безобразная намотка обмоток .

    • угомонись диванный эксперт, ты и такого не сможешь сделать.

  • eres un máquina....recablear el motor, pintar, desmontar, volver a montar....que crack!!

  • Мурчит как котёнок :))

  • I think 1930 all electronics have 110V... and I look it's too modern contructions for that period. I think that is 1950 up years... but you do very amazing work as usual🤙

  • Передний и задний декель двигателя нужно устанавливать вентиляционными отверстиями вниз, как показано на рисунке производителя в начале видео. Крыльчатка вентилятора также установлена обратной стороной.

    • Estoy de acuerdo , pero solo encajaban en esa posición , este motor fue diseñado para estar colgado del techo

  • You gotta be shitting me great job

  • Wow!

  • Brilliant job. I have a similar motor from the 1920s. One question though. After sandblasting why did you burnish the motor housing with a wire wheel? Paint sticks better to the rough finish.

    • Gracias , se le dio con el cepillo de alambre por qué si el acabado es demasiado bruto se verá reflejado en la pintura final

  • The far-flung married especially juggle because winter phylogentically disarm round a uptight bit. wistful, unwritten fall

  • Hice cientoss de esos motores ! Solo hay que tener cuidado con la plaqueta de no ronperta ! Saludos

  • wonderful job! it was nice to watch this restoration!

  • 23:33 The outer ring of the bearing rotates in the cover. I doubt it should be this way о_0

    • No gira , se le puso un bloqueador de rodamientos

  • 19:36 FORJA NEGRO - "что-то про негров" - подумал я. Наверно краска черная. И точно!

  • Работал на одном заводе...так там токарный и фрезерный станки фирмы ,вандерер, 1938 года и работали!

  • Vous n’avez jamais peur de ne pas y arriver ?

    • Si ,muchas veces 😂

  • Еле пердит, обмотки явно напутал.

  • Working out the electrical was the amazing part !

  • Unbelievable! You actually went for it and rewound it manually. That is some next level work there, Sir. Love it :)

  • it looks like the shaft is bent a little.

    • @My Relics You know better than me my friend. Great Job!

    • Está recto

  • You resurrected a motor that all whom made it are died

  • Очень захватывающее зрелище 👍 Всё время есть мысль - получится, или нет 🤔

    • я думаю если бы не получилось то этого видео не было бы.

  • Your refurbishing skill is amazing, respect your patience to bring a dead 90 yo motor to new life👍. But just wonder if the centrifugal switch worked properly? As the test speed looked much slower than 1,4xx rpm due to the switch did not cut the starting winding off to attain the running speed.🙂

    • gracias , las rpm del motor fueron medidas en el torno dando unas 1400 rpm en el video parece mas lento

  • Перебрать электродвигатель для русского парня это как два пальца обоссать !!

  • Eres muy bueno restaurando¡enhorabuena!

  • Ну хоть шайбы бы под гайки подложил.

    • lo tendré en cuenta , gracias !

  • That a hard hard hard work!!!!!thx for video!!!!gracias!!

    • gracias a ti por verlo!!!

  • ¿Por que cambias los tornillos por otros nuevos?

    • por que no se podían salvar

  • Was this used as a boat anchor?

    • no , pero por su peso puede valer para usar como ancla🤣

  • lol

  • LIFE is just like a painting, Draw with lines of hope... Erase your errors with your tolerance...Dip your brush with lots of patience...And COLOR it with LOVE !

  • 😱😱😱Me relajo esa concentración

    • me alegra que te relaje !!

  • 12.26 Вот теперь все готово к сдаче в металолом

  • Sweet stuff buddy!!!